Effects of Spray Parameters and Post-spray Heat Treatment on Microstructure and Mechanical Properties of Warm-Sprayed Ti-6Al-4V Coatings View Full Text


Ontology type: schema:ScholarlyArticle      Open Access: True


Article Info

DATE

2017-04

AUTHORS

R. M. Molak, H. Araki, M. Watanabe, H. Katanoda, N. Ohno, S. Kuroda

ABSTRACT

Warm spray is a novel thermal spray technique that allows the formation of dense and relatively pure Ti-6Al-4V coatings due to its capability to control the temperature of the propellant gas by diluting the combustion flame with an inert gas such as nitrogen. Recently, its combustion pressure has been increased from 1 to 4 MPa aiming to further increase particle velocity to over 1000 m/s. Two series of coatings with combustion pressure of 1 and 4 MPa and various nitrogen flow rates were prepared in this study. Effects of combustion pressure and nitrogen flow rate on the microstructure and mechanical properties of the Ti-6Al-4V coatings were systematically studied. Miniature tensile specimens with a total length of about 9 mm were used for static tensile tests. It was found that the spray parameters affect both the porosity and oxygen content of the coatings significantly and had remarkable effects on their mechanical properties. High level of porosity in the Ti-6Al-4V coatings reduced the effective cross-sectional area of the mini-specimens and caused a drop in their tensile strength and Young’s modulus. Subsequent heat treatments were found effective in significantly recovering the mechanical properties of the as-sprayed coatings. More... »

PAGES

627-647

References to SciGraph publications

  • 2013-08. Mechanical and Microstructural Characterization of Cold-Sprayed Ti-6Al-4V After Heat Treatment in JOURNAL OF THERMAL SPRAY TECHNOLOGY
  • 2011-06. Current Status and Future Prospects of Warm Spray Technology in JOURNAL OF THERMAL SPRAY TECHNOLOGY
  • 2012-06. Study of the Influence of Particle Velocity on Adhesive Strength of Cold Spray Deposits in JOURNAL OF THERMAL SPRAY TECHNOLOGY
  • 2012-03. The Effect of Deposition Conditions on Adhesion Strength of Ti and Ti6Al4V Cold Spray Splats in JOURNAL OF THERMAL SPRAY TECHNOLOGY
  • 2006-12. New developments in cold spray based on higher gas and particle temperatures in JOURNAL OF THERMAL SPRAY TECHNOLOGY
  • 2009-03. Recrystallization of Cold Spray-Fabricated CP Titanium Structures in JOURNAL OF THERMAL SPRAY TECHNOLOGY
  • 2006-06. The effect of a simple annealing heat treatment on the mechanical properties of cold-sprayed aluminum in JOURNAL OF THERMAL SPRAY TECHNOLOGY
  • 2014-01. Warm Spray Forming of Ti-6Al-4V in JOURNAL OF THERMAL SPRAY TECHNOLOGY
  • 1999-12. Particle velocity and deposition efficiency in the cold spray process in JOURNAL OF THERMAL SPRAY TECHNOLOGY
  • 2015-12. Effects of Spray Parameters and Heat Treatment on the Microstructure and Mechanical Properties of Titanium Coatings Formed by Warm Spraying in JOURNAL OF THERMAL SPRAY TECHNOLOGY
  • 2008-04. The Repair of Magnesium Rotorcraft Components by Cold Spray in JOURNAL OF FAILURE ANALYSIS AND PREVENTION
  • 2013-03. Cold Spray Forming of Inconel 718 in JOURNAL OF THERMAL SPRAY TECHNOLOGY
  • Identifiers

    URI

    http://scigraph.springernature.com/pub.10.1007/s11666-016-0494-5

    DOI

    http://dx.doi.org/10.1007/s11666-016-0494-5

    DIMENSIONS

    https://app.dimensions.ai/details/publication/pub.1001679420


    Indexing Status Check whether this publication has been indexed by Scopus and Web Of Science using the SN Indexing Status Tool
    Incoming Citations Browse incoming citations for this publication using opencitations.net

    JSON-LD is the canonical representation for SciGraph data.

    TIP: You can open this SciGraph record using an external JSON-LD service: JSON-LD Playground Google SDTT

    [
      {
        "@context": "https://springernature.github.io/scigraph/jsonld/sgcontext.json", 
        "about": [
          {
            "id": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/0915", 
            "inDefinedTermSet": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/", 
            "name": "Interdisciplinary Engineering", 
            "type": "DefinedTerm"
          }, 
          {
            "id": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/09", 
            "inDefinedTermSet": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/", 
            "name": "Engineering", 
            "type": "DefinedTerm"
          }
        ], 
        "author": [
          {
            "affiliation": {
              "alternateName": "National Institute for Materials Science", 
              "id": "https://www.grid.ac/institutes/grid.21941.3f", 
              "name": [
                "National Institute for Materials Science (NIMS), Tsukuba, Japan"
              ], 
              "type": "Organization"
            }, 
            "familyName": "Molak", 
            "givenName": "R. M.", 
            "id": "sg:person.014417165711.43", 
            "sameAs": [
              "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.014417165711.43"
            ], 
            "type": "Person"
          }, 
          {
            "affiliation": {
              "alternateName": "National Institute for Materials Science", 
              "id": "https://www.grid.ac/institutes/grid.21941.3f", 
              "name": [
                "National Institute for Materials Science (NIMS), Tsukuba, Japan"
              ], 
              "type": "Organization"
            }, 
            "familyName": "Araki", 
            "givenName": "H.", 
            "id": "sg:person.07472547145.74", 
            "sameAs": [
              "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.07472547145.74"
            ], 
            "type": "Person"
          }, 
          {
            "affiliation": {
              "alternateName": "National Institute for Materials Science", 
              "id": "https://www.grid.ac/institutes/grid.21941.3f", 
              "name": [
                "National Institute for Materials Science (NIMS), Tsukuba, Japan"
              ], 
              "type": "Organization"
            }, 
            "familyName": "Watanabe", 
            "givenName": "M.", 
            "id": "sg:person.016002542731.16", 
            "sameAs": [
              "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.016002542731.16"
            ], 
            "type": "Person"
          }, 
          {
            "affiliation": {
              "alternateName": "Kagoshima University", 
              "id": "https://www.grid.ac/institutes/grid.258333.c", 
              "name": [
                "Kagoshima University, Korimoto, Kagoshima, Japan"
              ], 
              "type": "Organization"
            }, 
            "familyName": "Katanoda", 
            "givenName": "H.", 
            "id": "sg:person.013637023663.55", 
            "sameAs": [
              "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.013637023663.55"
            ], 
            "type": "Person"
          }, 
          {
            "affiliation": {
              "name": [
                "Plasma Giken Co. Ltd., Toda, Saitama, Japan"
              ], 
              "type": "Organization"
            }, 
            "familyName": "Ohno", 
            "givenName": "N.", 
            "id": "sg:person.07770517357.30", 
            "sameAs": [
              "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.07770517357.30"
            ], 
            "type": "Person"
          }, 
          {
            "affiliation": {
              "alternateName": "National Institute for Materials Science", 
              "id": "https://www.grid.ac/institutes/grid.21941.3f", 
              "name": [
                "National Institute for Materials Science (NIMS), Tsukuba, Japan"
              ], 
              "type": "Organization"
            }, 
            "familyName": "Kuroda", 
            "givenName": "S.", 
            "id": "sg:person.014154046711.33", 
            "sameAs": [
              "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.014154046711.33"
            ], 
            "type": "Person"
          }
        ], 
        "citation": [
          {
            "id": "sg:pub.10.1007/s11666-015-0343-y", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1000685129", 
              "https://doi.org/10.1007/s11666-015-0343-y"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/j.apsusc.2011.07.107", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1001187430"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1080/01418610008212096", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1004437379"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s11666-012-9827-1", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1005839724", 
              "https://doi.org/10.1007/s11666-012-9827-1"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1361/105996306x147144", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1006341373", 
              "https://doi.org/10.1361/105996306x147144"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/j.actamat.2005.10.005", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1007253959"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s11666-013-9945-4", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1007979374", 
              "https://doi.org/10.1007/s11666-013-9945-4"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1361/105996399770350278", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1012776735", 
              "https://doi.org/10.1361/105996399770350278"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s11666-011-9720-3", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1013599518", 
              "https://doi.org/10.1007/s11666-011-9720-3"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s11666-011-9648-7", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1017253191", 
              "https://doi.org/10.1007/s11666-011-9648-7"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/s0026-0657(06)70713-5", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1018144169"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/j.actamat.2008.06.003", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1018320619"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s11666-011-9707-0", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1018390520", 
              "https://doi.org/10.1007/s11666-011-9707-0"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/j.msea.2015.11.037", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1018462632"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s11666-013-0024-7", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1019831888", 
              "https://doi.org/10.1007/s11666-013-0024-7"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s11666-013-0024-7", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1019831888", 
              "https://doi.org/10.1007/s11666-013-0024-7"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/j.surfcoat.2005.05.011", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1021113299"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1361/105996306x108138", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1023425098", 
              "https://doi.org/10.1361/105996306x108138"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/j.surfcoat.2008.04.011", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1024367496"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/j.scriptamat.2010.03.061", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1026852220"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s11666-008-9212-2", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1027269063", 
              "https://doi.org/10.1007/s11666-008-9212-2"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s11668-008-9116-y", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1030281961", 
              "https://doi.org/10.1007/s11668-008-9116-y"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/s1359-6462(03)00394-4", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1035404192"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/s1359-6462(03)00394-4", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1035404192"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/j.scriptamat.2008.06.020", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1039941549"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1088/1468-6996/9/3/033002", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1044665593"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1557/jmr.2002.0002", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1045433608"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/j.matdes.2004.03.008", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1048002911"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/j.cirp.2007.05.138", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1050660029"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1016/j.apsusc.2011.01.076", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1051708850"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.1557/proc-758-ll2.6", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1067956061"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.4028/www.scientific.net/amr.602-604.1604", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1072034042"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "https://doi.org/10.4028/www.scientific.net/msf.706-709.258", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1072137970"
            ], 
            "type": "CreativeWork"
          }
        ], 
        "datePublished": "2017-04", 
        "datePublishedReg": "2017-04-01", 
        "description": "Warm spray is a novel thermal spray technique that allows the formation of dense and relatively pure Ti-6Al-4V coatings due to its capability to control the temperature of the propellant gas by diluting the combustion flame with an inert gas such as nitrogen. Recently, its combustion pressure has been increased from 1 to 4 MPa aiming to further increase particle velocity to over 1000 m/s. Two series of coatings with combustion pressure of 1 and 4 MPa and various nitrogen flow rates were prepared in this study. Effects of combustion pressure and nitrogen flow rate on the microstructure and mechanical properties of the Ti-6Al-4V coatings were systematically studied. Miniature tensile specimens with a total length of about 9 mm were used for static tensile tests. It was found that the spray parameters affect both the porosity and oxygen content of the coatings significantly and had remarkable effects on their mechanical properties. High level of porosity in the Ti-6Al-4V coatings reduced the effective cross-sectional area of the mini-specimens and caused a drop in their tensile strength and Young\u2019s modulus. Subsequent heat treatments were found effective in significantly recovering the mechanical properties of the as-sprayed coatings.", 
        "genre": "research_article", 
        "id": "sg:pub.10.1007/s11666-016-0494-5", 
        "inLanguage": [
          "en"
        ], 
        "isAccessibleForFree": true, 
        "isPartOf": [
          {
            "id": "sg:journal.1136229", 
            "issn": [
              "1059-9630", 
              "1544-1016"
            ], 
            "name": "Journal of Thermal Spray Technology", 
            "type": "Periodical"
          }, 
          {
            "issueNumber": "4", 
            "type": "PublicationIssue"
          }, 
          {
            "type": "PublicationVolume", 
            "volumeNumber": "26"
          }
        ], 
        "name": "Effects of Spray Parameters and Post-spray Heat Treatment on Microstructure and Mechanical Properties of Warm-Sprayed Ti-6Al-4V Coatings", 
        "pagination": "627-647", 
        "productId": [
          {
            "name": "readcube_id", 
            "type": "PropertyValue", 
            "value": [
              "07ff8a087901e96814e94806194145d4c5339ddb07b062b7a85d339060d560a2"
            ]
          }, 
          {
            "name": "doi", 
            "type": "PropertyValue", 
            "value": [
              "10.1007/s11666-016-0494-5"
            ]
          }, 
          {
            "name": "dimensions_id", 
            "type": "PropertyValue", 
            "value": [
              "pub.1001679420"
            ]
          }
        ], 
        "sameAs": [
          "https://doi.org/10.1007/s11666-016-0494-5", 
          "https://app.dimensions.ai/details/publication/pub.1001679420"
        ], 
        "sdDataset": "articles", 
        "sdDatePublished": "2019-04-11T12:27", 
        "sdLicense": "https://scigraph.springernature.com/explorer/license/", 
        "sdPublisher": {
          "name": "Springer Nature - SN SciGraph project", 
          "type": "Organization"
        }, 
        "sdSource": "s3://com-uberresearch-data-dimensions-target-20181106-alternative/cleanup/v134/2549eaecd7973599484d7c17b260dba0a4ecb94b/merge/v9/a6c9fde33151104705d4d7ff012ea9563521a3ce/jats-lookup/v90/0000000362_0000000362/records_87119_00000000.jsonl", 
        "type": "ScholarlyArticle", 
        "url": "https://link.springer.com/10.1007%2Fs11666-016-0494-5"
      }
    ]
     

    Download the RDF metadata as:  json-ld nt turtle xml License info

    HOW TO GET THIS DATA PROGRAMMATICALLY:

    JSON-LD is a popular format for linked data which is fully compatible with JSON.

    curl -H 'Accept: application/ld+json' 'https://scigraph.springernature.com/pub.10.1007/s11666-016-0494-5'

    N-Triples is a line-based linked data format ideal for batch operations.

    curl -H 'Accept: application/n-triples' 'https://scigraph.springernature.com/pub.10.1007/s11666-016-0494-5'

    Turtle is a human-readable linked data format.

    curl -H 'Accept: text/turtle' 'https://scigraph.springernature.com/pub.10.1007/s11666-016-0494-5'

    RDF/XML is a standard XML format for linked data.

    curl -H 'Accept: application/rdf+xml' 'https://scigraph.springernature.com/pub.10.1007/s11666-016-0494-5'


     

    This table displays all metadata directly associated to this object as RDF triples.

    206 TRIPLES      21 PREDICATES      58 URIs      19 LITERALS      7 BLANK NODES

    Subject Predicate Object
    1 sg:pub.10.1007/s11666-016-0494-5 schema:about anzsrc-for:09
    2 anzsrc-for:0915
    3 schema:author N0bbfcd94af384d9a9f29691fd6e02c48
    4 schema:citation sg:pub.10.1007/s11666-008-9212-2
    5 sg:pub.10.1007/s11666-011-9648-7
    6 sg:pub.10.1007/s11666-011-9707-0
    7 sg:pub.10.1007/s11666-011-9720-3
    8 sg:pub.10.1007/s11666-012-9827-1
    9 sg:pub.10.1007/s11666-013-0024-7
    10 sg:pub.10.1007/s11666-013-9945-4
    11 sg:pub.10.1007/s11666-015-0343-y
    12 sg:pub.10.1007/s11668-008-9116-y
    13 sg:pub.10.1361/105996306x108138
    14 sg:pub.10.1361/105996306x147144
    15 sg:pub.10.1361/105996399770350278
    16 https://doi.org/10.1016/j.actamat.2005.10.005
    17 https://doi.org/10.1016/j.actamat.2008.06.003
    18 https://doi.org/10.1016/j.apsusc.2011.01.076
    19 https://doi.org/10.1016/j.apsusc.2011.07.107
    20 https://doi.org/10.1016/j.cirp.2007.05.138
    21 https://doi.org/10.1016/j.matdes.2004.03.008
    22 https://doi.org/10.1016/j.msea.2015.11.037
    23 https://doi.org/10.1016/j.scriptamat.2008.06.020
    24 https://doi.org/10.1016/j.scriptamat.2010.03.061
    25 https://doi.org/10.1016/j.surfcoat.2005.05.011
    26 https://doi.org/10.1016/j.surfcoat.2008.04.011
    27 https://doi.org/10.1016/s0026-0657(06)70713-5
    28 https://doi.org/10.1016/s1359-6462(03)00394-4
    29 https://doi.org/10.1080/01418610008212096
    30 https://doi.org/10.1088/1468-6996/9/3/033002
    31 https://doi.org/10.1557/jmr.2002.0002
    32 https://doi.org/10.1557/proc-758-ll2.6
    33 https://doi.org/10.4028/www.scientific.net/amr.602-604.1604
    34 https://doi.org/10.4028/www.scientific.net/msf.706-709.258
    35 schema:datePublished 2017-04
    36 schema:datePublishedReg 2017-04-01
    37 schema:description Warm spray is a novel thermal spray technique that allows the formation of dense and relatively pure Ti-6Al-4V coatings due to its capability to control the temperature of the propellant gas by diluting the combustion flame with an inert gas such as nitrogen. Recently, its combustion pressure has been increased from 1 to 4 MPa aiming to further increase particle velocity to over 1000 m/s. Two series of coatings with combustion pressure of 1 and 4 MPa and various nitrogen flow rates were prepared in this study. Effects of combustion pressure and nitrogen flow rate on the microstructure and mechanical properties of the Ti-6Al-4V coatings were systematically studied. Miniature tensile specimens with a total length of about 9 mm were used for static tensile tests. It was found that the spray parameters affect both the porosity and oxygen content of the coatings significantly and had remarkable effects on their mechanical properties. High level of porosity in the Ti-6Al-4V coatings reduced the effective cross-sectional area of the mini-specimens and caused a drop in their tensile strength and Young’s modulus. Subsequent heat treatments were found effective in significantly recovering the mechanical properties of the as-sprayed coatings.
    38 schema:genre research_article
    39 schema:inLanguage en
    40 schema:isAccessibleForFree true
    41 schema:isPartOf N11f7e2e4ba2b47309b44b4a4d7904e0f
    42 N7f0d763545524ffcabdf040f570ca8c8
    43 sg:journal.1136229
    44 schema:name Effects of Spray Parameters and Post-spray Heat Treatment on Microstructure and Mechanical Properties of Warm-Sprayed Ti-6Al-4V Coatings
    45 schema:pagination 627-647
    46 schema:productId Nd2dbfcab6f0c4c13a7708cb26d377490
    47 Ne3a1cb3a5e6443989bdf1c4062a1cdb9
    48 Ned2e98469cb94781bfc9a4758c98ca8e
    49 schema:sameAs https://app.dimensions.ai/details/publication/pub.1001679420
    50 https://doi.org/10.1007/s11666-016-0494-5
    51 schema:sdDatePublished 2019-04-11T12:27
    52 schema:sdLicense https://scigraph.springernature.com/explorer/license/
    53 schema:sdPublisher N6610d0570577451dba3e7e0ce9db51ec
    54 schema:url https://link.springer.com/10.1007%2Fs11666-016-0494-5
    55 sgo:license sg:explorer/license/
    56 sgo:sdDataset articles
    57 rdf:type schema:ScholarlyArticle
    58 N0bbfcd94af384d9a9f29691fd6e02c48 rdf:first sg:person.014417165711.43
    59 rdf:rest Ndb7d205a73824098928ee7f95283e192
    60 N11f7e2e4ba2b47309b44b4a4d7904e0f schema:volumeNumber 26
    61 rdf:type schema:PublicationVolume
    62 N3c003508698e4933a71246791abc6176 rdf:first sg:person.013637023663.55
    63 rdf:rest Ncf922d714ef54fca96c2c107b16eff13
    64 N6610d0570577451dba3e7e0ce9db51ec schema:name Springer Nature - SN SciGraph project
    65 rdf:type schema:Organization
    66 N7f0d763545524ffcabdf040f570ca8c8 schema:issueNumber 4
    67 rdf:type schema:PublicationIssue
    68 Nb95703b939d4487da194e1a476432c96 rdf:first sg:person.016002542731.16
    69 rdf:rest N3c003508698e4933a71246791abc6176
    70 Nb9f1769035fc408791c78d32c90d2710 rdf:first sg:person.014154046711.33
    71 rdf:rest rdf:nil
    72 Ncf922d714ef54fca96c2c107b16eff13 rdf:first sg:person.07770517357.30
    73 rdf:rest Nb9f1769035fc408791c78d32c90d2710
    74 Nd2dbfcab6f0c4c13a7708cb26d377490 schema:name doi
    75 schema:value 10.1007/s11666-016-0494-5
    76 rdf:type schema:PropertyValue
    77 Nd5105ebbed724866beb4d53d5f27fc98 schema:name Plasma Giken Co. Ltd., Toda, Saitama, Japan
    78 rdf:type schema:Organization
    79 Ndb7d205a73824098928ee7f95283e192 rdf:first sg:person.07472547145.74
    80 rdf:rest Nb95703b939d4487da194e1a476432c96
    81 Ne3a1cb3a5e6443989bdf1c4062a1cdb9 schema:name dimensions_id
    82 schema:value pub.1001679420
    83 rdf:type schema:PropertyValue
    84 Ned2e98469cb94781bfc9a4758c98ca8e schema:name readcube_id
    85 schema:value 07ff8a087901e96814e94806194145d4c5339ddb07b062b7a85d339060d560a2
    86 rdf:type schema:PropertyValue
    87 anzsrc-for:09 schema:inDefinedTermSet anzsrc-for:
    88 schema:name Engineering
    89 rdf:type schema:DefinedTerm
    90 anzsrc-for:0915 schema:inDefinedTermSet anzsrc-for:
    91 schema:name Interdisciplinary Engineering
    92 rdf:type schema:DefinedTerm
    93 sg:journal.1136229 schema:issn 1059-9630
    94 1544-1016
    95 schema:name Journal of Thermal Spray Technology
    96 rdf:type schema:Periodical
    97 sg:person.013637023663.55 schema:affiliation https://www.grid.ac/institutes/grid.258333.c
    98 schema:familyName Katanoda
    99 schema:givenName H.
    100 schema:sameAs https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.013637023663.55
    101 rdf:type schema:Person
    102 sg:person.014154046711.33 schema:affiliation https://www.grid.ac/institutes/grid.21941.3f
    103 schema:familyName Kuroda
    104 schema:givenName S.
    105 schema:sameAs https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.014154046711.33
    106 rdf:type schema:Person
    107 sg:person.014417165711.43 schema:affiliation https://www.grid.ac/institutes/grid.21941.3f
    108 schema:familyName Molak
    109 schema:givenName R. M.
    110 schema:sameAs https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.014417165711.43
    111 rdf:type schema:Person
    112 sg:person.016002542731.16 schema:affiliation https://www.grid.ac/institutes/grid.21941.3f
    113 schema:familyName Watanabe
    114 schema:givenName M.
    115 schema:sameAs https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.016002542731.16
    116 rdf:type schema:Person
    117 sg:person.07472547145.74 schema:affiliation https://www.grid.ac/institutes/grid.21941.3f
    118 schema:familyName Araki
    119 schema:givenName H.
    120 schema:sameAs https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.07472547145.74
    121 rdf:type schema:Person
    122 sg:person.07770517357.30 schema:affiliation Nd5105ebbed724866beb4d53d5f27fc98
    123 schema:familyName Ohno
    124 schema:givenName N.
    125 schema:sameAs https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.07770517357.30
    126 rdf:type schema:Person
    127 sg:pub.10.1007/s11666-008-9212-2 schema:sameAs https://app.dimensions.ai/details/publication/pub.1027269063
    128 https://doi.org/10.1007/s11666-008-9212-2
    129 rdf:type schema:CreativeWork
    130 sg:pub.10.1007/s11666-011-9648-7 schema:sameAs https://app.dimensions.ai/details/publication/pub.1017253191
    131 https://doi.org/10.1007/s11666-011-9648-7
    132 rdf:type schema:CreativeWork
    133 sg:pub.10.1007/s11666-011-9707-0 schema:sameAs https://app.dimensions.ai/details/publication/pub.1018390520
    134 https://doi.org/10.1007/s11666-011-9707-0
    135 rdf:type schema:CreativeWork
    136 sg:pub.10.1007/s11666-011-9720-3 schema:sameAs https://app.dimensions.ai/details/publication/pub.1013599518
    137 https://doi.org/10.1007/s11666-011-9720-3
    138 rdf:type schema:CreativeWork
    139 sg:pub.10.1007/s11666-012-9827-1 schema:sameAs https://app.dimensions.ai/details/publication/pub.1005839724
    140 https://doi.org/10.1007/s11666-012-9827-1
    141 rdf:type schema:CreativeWork
    142 sg:pub.10.1007/s11666-013-0024-7 schema:sameAs https://app.dimensions.ai/details/publication/pub.1019831888
    143 https://doi.org/10.1007/s11666-013-0024-7
    144 rdf:type schema:CreativeWork
    145 sg:pub.10.1007/s11666-013-9945-4 schema:sameAs https://app.dimensions.ai/details/publication/pub.1007979374
    146 https://doi.org/10.1007/s11666-013-9945-4
    147 rdf:type schema:CreativeWork
    148 sg:pub.10.1007/s11666-015-0343-y schema:sameAs https://app.dimensions.ai/details/publication/pub.1000685129
    149 https://doi.org/10.1007/s11666-015-0343-y
    150 rdf:type schema:CreativeWork
    151 sg:pub.10.1007/s11668-008-9116-y schema:sameAs https://app.dimensions.ai/details/publication/pub.1030281961
    152 https://doi.org/10.1007/s11668-008-9116-y
    153 rdf:type schema:CreativeWork
    154 sg:pub.10.1361/105996306x108138 schema:sameAs https://app.dimensions.ai/details/publication/pub.1023425098
    155 https://doi.org/10.1361/105996306x108138
    156 rdf:type schema:CreativeWork
    157 sg:pub.10.1361/105996306x147144 schema:sameAs https://app.dimensions.ai/details/publication/pub.1006341373
    158 https://doi.org/10.1361/105996306x147144
    159 rdf:type schema:CreativeWork
    160 sg:pub.10.1361/105996399770350278 schema:sameAs https://app.dimensions.ai/details/publication/pub.1012776735
    161 https://doi.org/10.1361/105996399770350278
    162 rdf:type schema:CreativeWork
    163 https://doi.org/10.1016/j.actamat.2005.10.005 schema:sameAs https://app.dimensions.ai/details/publication/pub.1007253959
    164 rdf:type schema:CreativeWork
    165 https://doi.org/10.1016/j.actamat.2008.06.003 schema:sameAs https://app.dimensions.ai/details/publication/pub.1018320619
    166 rdf:type schema:CreativeWork
    167 https://doi.org/10.1016/j.apsusc.2011.01.076 schema:sameAs https://app.dimensions.ai/details/publication/pub.1051708850
    168 rdf:type schema:CreativeWork
    169 https://doi.org/10.1016/j.apsusc.2011.07.107 schema:sameAs https://app.dimensions.ai/details/publication/pub.1001187430
    170 rdf:type schema:CreativeWork
    171 https://doi.org/10.1016/j.cirp.2007.05.138 schema:sameAs https://app.dimensions.ai/details/publication/pub.1050660029
    172 rdf:type schema:CreativeWork
    173 https://doi.org/10.1016/j.matdes.2004.03.008 schema:sameAs https://app.dimensions.ai/details/publication/pub.1048002911
    174 rdf:type schema:CreativeWork
    175 https://doi.org/10.1016/j.msea.2015.11.037 schema:sameAs https://app.dimensions.ai/details/publication/pub.1018462632
    176 rdf:type schema:CreativeWork
    177 https://doi.org/10.1016/j.scriptamat.2008.06.020 schema:sameAs https://app.dimensions.ai/details/publication/pub.1039941549
    178 rdf:type schema:CreativeWork
    179 https://doi.org/10.1016/j.scriptamat.2010.03.061 schema:sameAs https://app.dimensions.ai/details/publication/pub.1026852220
    180 rdf:type schema:CreativeWork
    181 https://doi.org/10.1016/j.surfcoat.2005.05.011 schema:sameAs https://app.dimensions.ai/details/publication/pub.1021113299
    182 rdf:type schema:CreativeWork
    183 https://doi.org/10.1016/j.surfcoat.2008.04.011 schema:sameAs https://app.dimensions.ai/details/publication/pub.1024367496
    184 rdf:type schema:CreativeWork
    185 https://doi.org/10.1016/s0026-0657(06)70713-5 schema:sameAs https://app.dimensions.ai/details/publication/pub.1018144169
    186 rdf:type schema:CreativeWork
    187 https://doi.org/10.1016/s1359-6462(03)00394-4 schema:sameAs https://app.dimensions.ai/details/publication/pub.1035404192
    188 rdf:type schema:CreativeWork
    189 https://doi.org/10.1080/01418610008212096 schema:sameAs https://app.dimensions.ai/details/publication/pub.1004437379
    190 rdf:type schema:CreativeWork
    191 https://doi.org/10.1088/1468-6996/9/3/033002 schema:sameAs https://app.dimensions.ai/details/publication/pub.1044665593
    192 rdf:type schema:CreativeWork
    193 https://doi.org/10.1557/jmr.2002.0002 schema:sameAs https://app.dimensions.ai/details/publication/pub.1045433608
    194 rdf:type schema:CreativeWork
    195 https://doi.org/10.1557/proc-758-ll2.6 schema:sameAs https://app.dimensions.ai/details/publication/pub.1067956061
    196 rdf:type schema:CreativeWork
    197 https://doi.org/10.4028/www.scientific.net/amr.602-604.1604 schema:sameAs https://app.dimensions.ai/details/publication/pub.1072034042
    198 rdf:type schema:CreativeWork
    199 https://doi.org/10.4028/www.scientific.net/msf.706-709.258 schema:sameAs https://app.dimensions.ai/details/publication/pub.1072137970
    200 rdf:type schema:CreativeWork
    201 https://www.grid.ac/institutes/grid.21941.3f schema:alternateName National Institute for Materials Science
    202 schema:name National Institute for Materials Science (NIMS), Tsukuba, Japan
    203 rdf:type schema:Organization
    204 https://www.grid.ac/institutes/grid.258333.c schema:alternateName Kagoshima University
    205 schema:name Kagoshima University, Korimoto, Kagoshima, Japan
    206 rdf:type schema:Organization
     




    Preview window. Press ESC to close (or click here)


    ...