Effects of Nozzle Radial Position, Separation Angle, and Gas Flow Partitioning on the Mixing, Eye Area, and Wall Shear Stress ... View Full Text


Ontology type: schema:ScholarlyArticle     


Article Info

DATE

2019-03-12

AUTHORS

A. N. Conejo, Rishikesh Mishra, D. Mazumdar

ABSTRACT

Mixing time, slag eye area, and wall shear stress in a ladle fitted with dual plugs have been studied as a function of operating variables, namely, gas flow rate, radial nozzle position, separation angle between nozzles and flow rate partitioning. While the mixing time and slag eye area have been experimentally investigated in a scaled water model (with and without a top slag layer), the shear stress on the vessel wall has been studied computationally via a RANS-based turbulent, three-dimensional coupled Eulerian–Lagrangian (VOF-DPM), multiphase flow model. Experimental and computational results have indicated that the mixing, eye area, and wall shear stress depend on the gas flow rate, i.e., while mixing efficiency increases with the increasing gas flow rate, the slag eye area, and wall shear stress, in contrast, become more pronounced with the increasing gas flow, leading to an undesirable operating regime. The radial nozzle position, separation angle between the nozzles and flow rate partitioning at any given flow rate also influence the ladle process performance, influencing the mixing, eye area, and wall shear stress, albeit to a varied degree. Within the range of operating conditions studied, an expected inverse correspondence between mixing time and shear behavior was observed. Experimental and computational results in conjunction have indicated that the best arrangement of porous plugs or gas injection nozzles for superior ladle process performance is dependent on the gas flow rate and is specific to the desired objective (i.e., decreasing the mixing time, or slag eye area and wall shear stress). Hence, a unique gas injection practice cannot and should not be suggested as the optimum for ladle metallurgy in steelmaking. Nevertheless, if the mixing time is the parameter of primary interest, a nozzle configuration with equal flow partitioning (1:1) between the nozzles and identical nozzle radial positions (0.7R/0.7R, 45 deg) should suffice for both low and high gas flow rates. In contrast, a nonidentical nozzle radial position (0.7R/0.5R, 90 deg) and an unequal gas flow rate per nozzle (1:3) appear preferable if both ladle eye and shear stresses, rather than mixing, are the issues of concern. More... »

PAGES

1-13

Identifiers

URI

http://scigraph.springernature.com/pub.10.1007/s11663-019-01546-8

DOI

http://dx.doi.org/10.1007/s11663-019-01546-8

DIMENSIONS

https://app.dimensions.ai/details/publication/pub.1112703409


Indexing Status Check whether this publication has been indexed by Scopus and Web Of Science using the SN Indexing Status Tool
Incoming Citations Browse incoming citations for this publication using opencitations.net

JSON-LD is the canonical representation for SciGraph data.

TIP: You can open this SciGraph record using an external JSON-LD service: JSON-LD Playground Google SDTT

[
  {
    "@context": "https://springernature.github.io/scigraph/jsonld/sgcontext.json", 
    "about": [
      {
        "id": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/0915", 
        "inDefinedTermSet": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/", 
        "name": "Interdisciplinary Engineering", 
        "type": "DefinedTerm"
      }, 
      {
        "id": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/09", 
        "inDefinedTermSet": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/", 
        "name": "Engineering", 
        "type": "DefinedTerm"
      }
    ], 
    "author": [
      {
        "affiliation": {
          "alternateName": "University of Science and Technology Beijing", 
          "id": "https://www.grid.ac/institutes/grid.69775.3a", 
          "name": [
            "School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing (USTB), 30 Xueyuan Road, Haidian District, 100083, Beijing, People\u2019s Republic of China", 
            "Ferrous Metallurgy Research Institute (FeMRI), Morelia, Mexico"
          ], 
          "type": "Organization"
        }, 
        "familyName": "Conejo", 
        "givenName": "A. N.", 
        "type": "Person"
      }, 
      {
        "affiliation": {
          "alternateName": "Indian Institute of Technology Kanpur", 
          "id": "https://www.grid.ac/institutes/grid.417965.8", 
          "name": [
            "Department of Materials Science and Engineering, Indian Institute of Technology Kanpur (IITK), 208016, Kanpur, UP, India"
          ], 
          "type": "Organization"
        }, 
        "familyName": "Mishra", 
        "givenName": "Rishikesh", 
        "type": "Person"
      }, 
      {
        "affiliation": {
          "alternateName": "Indian Institute of Technology Kanpur", 
          "id": "https://www.grid.ac/institutes/grid.417965.8", 
          "name": [
            "Department of Materials Science and Engineering, Indian Institute of Technology Kanpur (IITK), 208016, Kanpur, UP, India"
          ], 
          "type": "Organization"
        }, 
        "familyName": "Mazumdar", 
        "givenName": "D.", 
        "type": "Person"
      }
    ], 
    "citation": [
      {
        "id": "https://doi.org/10.1179/174328109x445732", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1000760804"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.1179/cmq.1989.28.1.19", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1003109279"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.2355/isijinternational.35.472", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1003315580"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.1021/je049922y", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1003681535"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.1021/je049922y", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1003681535"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/bf02654323", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1006407032", 
          "https://doi.org/10.1007/bf02654323"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/bf02654323", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1006407032", 
          "https://doi.org/10.1007/bf02654323"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.1016/b978-0-08-096984-8.00002-1", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1007908769"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.2355/isijinternational.isijint-2016-360", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1014008499"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/bf02657818", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1014027865", 
          "https://doi.org/10.1007/bf02657818"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/bf02657818", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1014027865", 
          "https://doi.org/10.1007/bf02657818"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.2355/isijinternational1966.25.14", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1016904172"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.1002/srin.200001324", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1019433583"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.2355/isijinternational.44.447", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1019881853"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/bf02657751", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1020572734", 
          "https://doi.org/10.1007/bf02657751"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/bf02657751", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1020572734", 
          "https://doi.org/10.1007/bf02657751"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.2355/isijinternational1966.23.43", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1021067616"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/bf02656455", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1021215418", 
          "https://doi.org/10.1007/bf02656455"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/bf02656455", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1021215418", 
          "https://doi.org/10.1007/bf02656455"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.2355/isijinternational.35.1", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1021519689"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/s11663-014-0263-0", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1023016018", 
          "https://doi.org/10.1007/s11663-014-0263-0"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.1002/srin.201200086", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1024515512"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/bf02650195", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1032121952", 
          "https://doi.org/10.1007/bf02650195"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/bf02650195", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1032121952", 
          "https://doi.org/10.1007/bf02650195"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.2355/isijinternational.31.1371", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1035468567"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.2355/isijinternational1966.23.169", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1035714330"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.2355/isijinternational.55.1", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1036980432"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.1179/cmq.1983.22.3.313", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1038453559"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.2355/isijinternational.48.1033", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1046493019"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.1016/0045-7930(94)00032-t", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1051218144"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.2355/isijinternational.isijint-2015-701", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1083878663"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/s11663-017-0992-y", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1085446521", 
          "https://doi.org/10.1007/s11663-017-0992-y"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/s11663-017-0992-y", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1085446521", 
          "https://doi.org/10.1007/s11663-017-0992-y"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "https://doi.org/10.1080/10426914.2017.1401722", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1092758006"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/s11663-018-1177-z", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1100746427", 
          "https://doi.org/10.1007/s11663-018-1177-z"
        ], 
        "type": "CreativeWork"
      }, 
      {
        "id": "sg:pub.10.1007/s11837-018-2977-y", 
        "sameAs": [
          "https://app.dimensions.ai/details/publication/pub.1104990145", 
          "https://doi.org/10.1007/s11837-018-2977-y"
        ], 
        "type": "CreativeWork"
      }
    ], 
    "datePublished": "2019-03-12", 
    "datePublishedReg": "2019-03-12", 
    "description": "Mixing time, slag eye area, and wall shear stress in a ladle fitted with dual plugs have been studied as a function of operating variables, namely, gas flow rate, radial nozzle position, separation angle between nozzles and flow rate partitioning. While the mixing time and slag eye area have been experimentally investigated in a scaled water model (with and without a top slag layer), the shear stress on the vessel wall has been studied computationally via a RANS-based turbulent, three-dimensional coupled Eulerian\u2013Lagrangian (VOF-DPM), multiphase flow model. Experimental and computational results have indicated that the mixing, eye area, and wall shear stress depend on the gas flow rate, i.e., while mixing efficiency increases with the increasing gas flow rate, the slag eye area, and wall shear stress, in contrast, become more pronounced with the increasing gas flow, leading to an undesirable operating regime. The radial nozzle position, separation angle between the nozzles and flow rate partitioning at any given flow rate also influence the ladle process performance, influencing the mixing, eye area, and wall shear stress, albeit to a varied degree. Within the range of operating conditions studied, an expected inverse correspondence between mixing time and shear behavior was observed. Experimental and computational results in conjunction have indicated that the best arrangement of porous plugs or gas injection nozzles for superior ladle process performance is dependent on the gas flow rate and is specific to the desired objective (i.e., decreasing the mixing time, or slag eye area and wall shear stress). Hence, a unique gas injection practice cannot and should not be suggested as the optimum for ladle metallurgy in steelmaking. Nevertheless, if the mixing time is the parameter of primary interest, a nozzle configuration with equal flow partitioning (1:1) between the nozzles and identical nozzle radial positions (0.7R/0.7R, 45 deg) should suffice for both low and high gas flow rates. In contrast, a nonidentical nozzle radial position (0.7R/0.5R, 90 deg) and an unequal gas flow rate per nozzle (1:3) appear preferable if both ladle eye and shear stresses, rather than mixing, are the issues of concern.", 
    "genre": "research_article", 
    "id": "sg:pub.10.1007/s11663-019-01546-8", 
    "inLanguage": [
      "en"
    ], 
    "isAccessibleForFree": false, 
    "isPartOf": [
      {
        "id": "sg:journal.1136775", 
        "issn": [
          "1073-5615", 
          "1543-1916"
        ], 
        "name": "Metallurgical and Materials Transactions B", 
        "type": "Periodical"
      }
    ], 
    "name": "Effects of Nozzle Radial Position, Separation Angle, and Gas Flow Partitioning on the Mixing, Eye Area, and Wall Shear Stress in Ladles Fitted with Dual Plugs", 
    "pagination": "1-13", 
    "productId": [
      {
        "name": "readcube_id", 
        "type": "PropertyValue", 
        "value": [
          "b42d8a3023592065c9e6c2937c0a82f595ba87605ecde7b4cb76f8fb29a4c07d"
        ]
      }, 
      {
        "name": "doi", 
        "type": "PropertyValue", 
        "value": [
          "10.1007/s11663-019-01546-8"
        ]
      }, 
      {
        "name": "dimensions_id", 
        "type": "PropertyValue", 
        "value": [
          "pub.1112703409"
        ]
      }
    ], 
    "sameAs": [
      "https://doi.org/10.1007/s11663-019-01546-8", 
      "https://app.dimensions.ai/details/publication/pub.1112703409"
    ], 
    "sdDataset": "articles", 
    "sdDatePublished": "2019-04-11T11:46", 
    "sdLicense": "https://scigraph.springernature.com/explorer/license/", 
    "sdPublisher": {
      "name": "Springer Nature - SN SciGraph project", 
      "type": "Organization"
    }, 
    "sdSource": "s3://com-uberresearch-data-dimensions-target-20181106-alternative/cleanup/v134/2549eaecd7973599484d7c17b260dba0a4ecb94b/merge/v9/a6c9fde33151104705d4d7ff012ea9563521a3ce/jats-lookup/v90/0000000358_0000000358/records_127459_00000011.jsonl", 
    "type": "ScholarlyArticle", 
    "url": "https://link.springer.com/10.1007%2Fs11663-019-01546-8"
  }
]
 

Download the RDF metadata as:  json-ld nt turtle xml License info

HOW TO GET THIS DATA PROGRAMMATICALLY:

JSON-LD is a popular format for linked data which is fully compatible with JSON.

curl -H 'Accept: application/ld+json' 'https://scigraph.springernature.com/pub.10.1007/s11663-019-01546-8'

N-Triples is a line-based linked data format ideal for batch operations.

curl -H 'Accept: application/n-triples' 'https://scigraph.springernature.com/pub.10.1007/s11663-019-01546-8'

Turtle is a human-readable linked data format.

curl -H 'Accept: text/turtle' 'https://scigraph.springernature.com/pub.10.1007/s11663-019-01546-8'

RDF/XML is a standard XML format for linked data.

curl -H 'Accept: application/rdf+xml' 'https://scigraph.springernature.com/pub.10.1007/s11663-019-01546-8'


 

This table displays all metadata directly associated to this object as RDF triples.

166 TRIPLES      21 PREDICATES      53 URIs      16 LITERALS      5 BLANK NODES

Subject Predicate Object
1 sg:pub.10.1007/s11663-019-01546-8 schema:about anzsrc-for:09
2 anzsrc-for:0915
3 schema:author N6b4ba159d0d54a539f1e654d2f1c6261
4 schema:citation sg:pub.10.1007/bf02650195
5 sg:pub.10.1007/bf02654323
6 sg:pub.10.1007/bf02656455
7 sg:pub.10.1007/bf02657751
8 sg:pub.10.1007/bf02657818
9 sg:pub.10.1007/s11663-014-0263-0
10 sg:pub.10.1007/s11663-017-0992-y
11 sg:pub.10.1007/s11663-018-1177-z
12 sg:pub.10.1007/s11837-018-2977-y
13 https://doi.org/10.1002/srin.200001324
14 https://doi.org/10.1002/srin.201200086
15 https://doi.org/10.1016/0045-7930(94)00032-t
16 https://doi.org/10.1016/b978-0-08-096984-8.00002-1
17 https://doi.org/10.1021/je049922y
18 https://doi.org/10.1080/10426914.2017.1401722
19 https://doi.org/10.1179/174328109x445732
20 https://doi.org/10.1179/cmq.1983.22.3.313
21 https://doi.org/10.1179/cmq.1989.28.1.19
22 https://doi.org/10.2355/isijinternational.31.1371
23 https://doi.org/10.2355/isijinternational.35.1
24 https://doi.org/10.2355/isijinternational.35.472
25 https://doi.org/10.2355/isijinternational.44.447
26 https://doi.org/10.2355/isijinternational.48.1033
27 https://doi.org/10.2355/isijinternational.55.1
28 https://doi.org/10.2355/isijinternational.isijint-2015-701
29 https://doi.org/10.2355/isijinternational.isijint-2016-360
30 https://doi.org/10.2355/isijinternational1966.23.169
31 https://doi.org/10.2355/isijinternational1966.23.43
32 https://doi.org/10.2355/isijinternational1966.25.14
33 schema:datePublished 2019-03-12
34 schema:datePublishedReg 2019-03-12
35 schema:description Mixing time, slag eye area, and wall shear stress in a ladle fitted with dual plugs have been studied as a function of operating variables, namely, gas flow rate, radial nozzle position, separation angle between nozzles and flow rate partitioning. While the mixing time and slag eye area have been experimentally investigated in a scaled water model (with and without a top slag layer), the shear stress on the vessel wall has been studied computationally via a RANS-based turbulent, three-dimensional coupled Eulerian–Lagrangian (VOF-DPM), multiphase flow model. Experimental and computational results have indicated that the mixing, eye area, and wall shear stress depend on the gas flow rate, i.e., while mixing efficiency increases with the increasing gas flow rate, the slag eye area, and wall shear stress, in contrast, become more pronounced with the increasing gas flow, leading to an undesirable operating regime. The radial nozzle position, separation angle between the nozzles and flow rate partitioning at any given flow rate also influence the ladle process performance, influencing the mixing, eye area, and wall shear stress, albeit to a varied degree. Within the range of operating conditions studied, an expected inverse correspondence between mixing time and shear behavior was observed. Experimental and computational results in conjunction have indicated that the best arrangement of porous plugs or gas injection nozzles for superior ladle process performance is dependent on the gas flow rate and is specific to the desired objective (i.e., decreasing the mixing time, or slag eye area and wall shear stress). Hence, a unique gas injection practice cannot and should not be suggested as the optimum for ladle metallurgy in steelmaking. Nevertheless, if the mixing time is the parameter of primary interest, a nozzle configuration with equal flow partitioning (1:1) between the nozzles and identical nozzle radial positions (0.7R/0.7R, 45 deg) should suffice for both low and high gas flow rates. In contrast, a nonidentical nozzle radial position (0.7R/0.5R, 90 deg) and an unequal gas flow rate per nozzle (1:3) appear preferable if both ladle eye and shear stresses, rather than mixing, are the issues of concern.
36 schema:genre research_article
37 schema:inLanguage en
38 schema:isAccessibleForFree false
39 schema:isPartOf sg:journal.1136775
40 schema:name Effects of Nozzle Radial Position, Separation Angle, and Gas Flow Partitioning on the Mixing, Eye Area, and Wall Shear Stress in Ladles Fitted with Dual Plugs
41 schema:pagination 1-13
42 schema:productId N5ec089dc7cbd4b138c8ab6d18a24af32
43 N96c827b62efa40fc9075c784195a477e
44 Ne7d976bc98424f99a45502d1c3c62108
45 schema:sameAs https://app.dimensions.ai/details/publication/pub.1112703409
46 https://doi.org/10.1007/s11663-019-01546-8
47 schema:sdDatePublished 2019-04-11T11:46
48 schema:sdLicense https://scigraph.springernature.com/explorer/license/
49 schema:sdPublisher N6375af7bb44d48a680805023ad979651
50 schema:url https://link.springer.com/10.1007%2Fs11663-019-01546-8
51 sgo:license sg:explorer/license/
52 sgo:sdDataset articles
53 rdf:type schema:ScholarlyArticle
54 N16c38caa8b8a4a61b0d06a0a47265294 schema:affiliation https://www.grid.ac/institutes/grid.417965.8
55 schema:familyName Mazumdar
56 schema:givenName D.
57 rdf:type schema:Person
58 N39e60230526048a394466b25f46038cd rdf:first N16c38caa8b8a4a61b0d06a0a47265294
59 rdf:rest rdf:nil
60 N5ec089dc7cbd4b138c8ab6d18a24af32 schema:name doi
61 schema:value 10.1007/s11663-019-01546-8
62 rdf:type schema:PropertyValue
63 N6375af7bb44d48a680805023ad979651 schema:name Springer Nature - SN SciGraph project
64 rdf:type schema:Organization
65 N6b4ba159d0d54a539f1e654d2f1c6261 rdf:first Na09ce6dca175454eb5b79c20d4fcf860
66 rdf:rest Nfc7f0b79f0cc48adb33fc72bb7c13d14
67 N96c827b62efa40fc9075c784195a477e schema:name readcube_id
68 schema:value b42d8a3023592065c9e6c2937c0a82f595ba87605ecde7b4cb76f8fb29a4c07d
69 rdf:type schema:PropertyValue
70 Na09ce6dca175454eb5b79c20d4fcf860 schema:affiliation https://www.grid.ac/institutes/grid.69775.3a
71 schema:familyName Conejo
72 schema:givenName A. N.
73 rdf:type schema:Person
74 Ne25f115fb42343c7964bdcf22e76cc55 schema:affiliation https://www.grid.ac/institutes/grid.417965.8
75 schema:familyName Mishra
76 schema:givenName Rishikesh
77 rdf:type schema:Person
78 Ne7d976bc98424f99a45502d1c3c62108 schema:name dimensions_id
79 schema:value pub.1112703409
80 rdf:type schema:PropertyValue
81 Nfc7f0b79f0cc48adb33fc72bb7c13d14 rdf:first Ne25f115fb42343c7964bdcf22e76cc55
82 rdf:rest N39e60230526048a394466b25f46038cd
83 anzsrc-for:09 schema:inDefinedTermSet anzsrc-for:
84 schema:name Engineering
85 rdf:type schema:DefinedTerm
86 anzsrc-for:0915 schema:inDefinedTermSet anzsrc-for:
87 schema:name Interdisciplinary Engineering
88 rdf:type schema:DefinedTerm
89 sg:journal.1136775 schema:issn 1073-5615
90 1543-1916
91 schema:name Metallurgical and Materials Transactions B
92 rdf:type schema:Periodical
93 sg:pub.10.1007/bf02650195 schema:sameAs https://app.dimensions.ai/details/publication/pub.1032121952
94 https://doi.org/10.1007/bf02650195
95 rdf:type schema:CreativeWork
96 sg:pub.10.1007/bf02654323 schema:sameAs https://app.dimensions.ai/details/publication/pub.1006407032
97 https://doi.org/10.1007/bf02654323
98 rdf:type schema:CreativeWork
99 sg:pub.10.1007/bf02656455 schema:sameAs https://app.dimensions.ai/details/publication/pub.1021215418
100 https://doi.org/10.1007/bf02656455
101 rdf:type schema:CreativeWork
102 sg:pub.10.1007/bf02657751 schema:sameAs https://app.dimensions.ai/details/publication/pub.1020572734
103 https://doi.org/10.1007/bf02657751
104 rdf:type schema:CreativeWork
105 sg:pub.10.1007/bf02657818 schema:sameAs https://app.dimensions.ai/details/publication/pub.1014027865
106 https://doi.org/10.1007/bf02657818
107 rdf:type schema:CreativeWork
108 sg:pub.10.1007/s11663-014-0263-0 schema:sameAs https://app.dimensions.ai/details/publication/pub.1023016018
109 https://doi.org/10.1007/s11663-014-0263-0
110 rdf:type schema:CreativeWork
111 sg:pub.10.1007/s11663-017-0992-y schema:sameAs https://app.dimensions.ai/details/publication/pub.1085446521
112 https://doi.org/10.1007/s11663-017-0992-y
113 rdf:type schema:CreativeWork
114 sg:pub.10.1007/s11663-018-1177-z schema:sameAs https://app.dimensions.ai/details/publication/pub.1100746427
115 https://doi.org/10.1007/s11663-018-1177-z
116 rdf:type schema:CreativeWork
117 sg:pub.10.1007/s11837-018-2977-y schema:sameAs https://app.dimensions.ai/details/publication/pub.1104990145
118 https://doi.org/10.1007/s11837-018-2977-y
119 rdf:type schema:CreativeWork
120 https://doi.org/10.1002/srin.200001324 schema:sameAs https://app.dimensions.ai/details/publication/pub.1019433583
121 rdf:type schema:CreativeWork
122 https://doi.org/10.1002/srin.201200086 schema:sameAs https://app.dimensions.ai/details/publication/pub.1024515512
123 rdf:type schema:CreativeWork
124 https://doi.org/10.1016/0045-7930(94)00032-t schema:sameAs https://app.dimensions.ai/details/publication/pub.1051218144
125 rdf:type schema:CreativeWork
126 https://doi.org/10.1016/b978-0-08-096984-8.00002-1 schema:sameAs https://app.dimensions.ai/details/publication/pub.1007908769
127 rdf:type schema:CreativeWork
128 https://doi.org/10.1021/je049922y schema:sameAs https://app.dimensions.ai/details/publication/pub.1003681535
129 rdf:type schema:CreativeWork
130 https://doi.org/10.1080/10426914.2017.1401722 schema:sameAs https://app.dimensions.ai/details/publication/pub.1092758006
131 rdf:type schema:CreativeWork
132 https://doi.org/10.1179/174328109x445732 schema:sameAs https://app.dimensions.ai/details/publication/pub.1000760804
133 rdf:type schema:CreativeWork
134 https://doi.org/10.1179/cmq.1983.22.3.313 schema:sameAs https://app.dimensions.ai/details/publication/pub.1038453559
135 rdf:type schema:CreativeWork
136 https://doi.org/10.1179/cmq.1989.28.1.19 schema:sameAs https://app.dimensions.ai/details/publication/pub.1003109279
137 rdf:type schema:CreativeWork
138 https://doi.org/10.2355/isijinternational.31.1371 schema:sameAs https://app.dimensions.ai/details/publication/pub.1035468567
139 rdf:type schema:CreativeWork
140 https://doi.org/10.2355/isijinternational.35.1 schema:sameAs https://app.dimensions.ai/details/publication/pub.1021519689
141 rdf:type schema:CreativeWork
142 https://doi.org/10.2355/isijinternational.35.472 schema:sameAs https://app.dimensions.ai/details/publication/pub.1003315580
143 rdf:type schema:CreativeWork
144 https://doi.org/10.2355/isijinternational.44.447 schema:sameAs https://app.dimensions.ai/details/publication/pub.1019881853
145 rdf:type schema:CreativeWork
146 https://doi.org/10.2355/isijinternational.48.1033 schema:sameAs https://app.dimensions.ai/details/publication/pub.1046493019
147 rdf:type schema:CreativeWork
148 https://doi.org/10.2355/isijinternational.55.1 schema:sameAs https://app.dimensions.ai/details/publication/pub.1036980432
149 rdf:type schema:CreativeWork
150 https://doi.org/10.2355/isijinternational.isijint-2015-701 schema:sameAs https://app.dimensions.ai/details/publication/pub.1083878663
151 rdf:type schema:CreativeWork
152 https://doi.org/10.2355/isijinternational.isijint-2016-360 schema:sameAs https://app.dimensions.ai/details/publication/pub.1014008499
153 rdf:type schema:CreativeWork
154 https://doi.org/10.2355/isijinternational1966.23.169 schema:sameAs https://app.dimensions.ai/details/publication/pub.1035714330
155 rdf:type schema:CreativeWork
156 https://doi.org/10.2355/isijinternational1966.23.43 schema:sameAs https://app.dimensions.ai/details/publication/pub.1021067616
157 rdf:type schema:CreativeWork
158 https://doi.org/10.2355/isijinternational1966.25.14 schema:sameAs https://app.dimensions.ai/details/publication/pub.1016904172
159 rdf:type schema:CreativeWork
160 https://www.grid.ac/institutes/grid.417965.8 schema:alternateName Indian Institute of Technology Kanpur
161 schema:name Department of Materials Science and Engineering, Indian Institute of Technology Kanpur (IITK), 208016, Kanpur, UP, India
162 rdf:type schema:Organization
163 https://www.grid.ac/institutes/grid.69775.3a schema:alternateName University of Science and Technology Beijing
164 schema:name Ferrous Metallurgy Research Institute (FeMRI), Morelia, Mexico
165 School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing (USTB), 30 Xueyuan Road, Haidian District, 100083, Beijing, People’s Republic of China
166 rdf:type schema:Organization
 




Preview window. Press ESC to close (or click here)


...