Metastable effects on martensitic transformation in SMA View Full Text


Ontology type: schema:ScholarlyArticle     


Article Info

DATE

2009-12-10

AUTHORS

V. Torra, C. Auguet, A. Isalgue, F. C. Lovey, A. Sepulveda, H. Soul

ABSTRACT

The use of Shape Memory Alloys (SMA) in technical applications as damping in civil engineering structures requires the characterization of the alloy for each specific application. This involves the evolution of the mechanical properties and damping capacity with the number of cycles, frequency, maximum deformation, applied stresses, and the evolution of the alloy with aging time and temperature. In particular, the temperature effects associated to self-heating need to be evaluated. In continuous cycling the effects of latent heat, the associated dissipation induced by the hysteresis, the heat flow to surroundings and the cycling frequency induce different states of temperature in the specimen, which in turn produces changes in the transformation-retransformation stresses. In this article, the temperature effects associated to cycling are outlined for different cycling frequencies. The results show that, for relatively faster frequency the temperature arrives at an oscillatory state superimposed to an exponential increase. For lower frequencies, some parts of the sample attain temperatures below room temperature. The experimental results are represented with an elementary model (the 1-body model or the Tian equation used in calorimetric representation) of heat transfer. For the higher fracture where life requirements are associated to damping in stayed cables for bridges, the results show (for the NiTi alloy) a reduction of the hysteresis width as the frequency increases for deformations up to 8%. For reduced deformation, under 2% appears an asymptotic behavior where the frictional area is practically independent of the cycling frequency (up to 20 Hz). In addition, it is shown that more than 4 million of working cycles can be attained if the maximum applied stress is kept below a threshold of about 200 MPa. Although under this condition the deformation must remain lower than 2% a reasonable damping capacity can still be obtained. More... »

PAGES

671-680

References to SciGraph publications

  • 2008-03. Metastable effects on martensitic transformation in SMA in JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY
  • 2007-05-15. Metastable effects onmartensitic transformation in SMA in JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY
  • 2008-04. Metastable effects on martensitic transformation in SMA part VII. Aging problems in NiTi in JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY
  • 2005-07. Metastable effects on martensitic transformation in SMA (I) recoverable effects by the action of thermodynamic forces in parent phase in JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY
  • 2007-10-13. Metastable effects on martensitic transformation in SMA part V. fatigue-life and detailed hysteresis behavior in NiTi and Cu-based alloys in JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY
  • 2007-07-19. Metastable effects on martensitic transformation in SMA in JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY
  • 2007-07-12. Metastable effects on martensitic transformation in SMA in JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY
  • Identifiers

    URI

    http://scigraph.springernature.com/pub.10.1007/s10973-009-0613-3

    DOI

    http://dx.doi.org/10.1007/s10973-009-0613-3

    DIMENSIONS

    https://app.dimensions.ai/details/publication/pub.1014929711


    Indexing Status Check whether this publication has been indexed by Scopus and Web Of Science using the SN Indexing Status Tool
    Incoming Citations Browse incoming citations for this publication using opencitations.net

    JSON-LD is the canonical representation for SciGraph data.

    TIP: You can open this SciGraph record using an external JSON-LD service: JSON-LD Playground Google SDTT

    [
      {
        "@context": "https://springernature.github.io/scigraph/jsonld/sgcontext.json", 
        "about": [
          {
            "id": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/03", 
            "inDefinedTermSet": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/", 
            "name": "Chemical Sciences", 
            "type": "DefinedTerm"
          }, 
          {
            "id": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/0303", 
            "inDefinedTermSet": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/", 
            "name": "Macromolecular and Materials Chemistry", 
            "type": "DefinedTerm"
          }, 
          {
            "id": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/0306", 
            "inDefinedTermSet": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/", 
            "name": "Physical Chemistry (incl. Structural)", 
            "type": "DefinedTerm"
          }, 
          {
            "id": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/0399", 
            "inDefinedTermSet": "http://purl.org/au-research/vocabulary/anzsrc-for/2008/", 
            "name": "Other Chemical Sciences", 
            "type": "DefinedTerm"
          }
        ], 
        "author": [
          {
            "affiliation": {
              "alternateName": "CIRG, DFA, ETSECCPB, UPC, Campus Nord B4, 08034, Barcelona, Catalonia, Spain", 
              "id": "http://www.grid.ac/institutes/grid.6835.8", 
              "name": [
                "CIRG, DFA, ETSECCPB, UPC, Campus Nord B4, 08034, Barcelona, Catalonia, Spain"
              ], 
              "type": "Organization"
            }, 
            "familyName": "Torra", 
            "givenName": "V.", 
            "id": "sg:person.013230703661.66", 
            "sameAs": [
              "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.013230703661.66"
            ], 
            "type": "Person"
          }, 
          {
            "affiliation": {
              "alternateName": "CIRG, DFA, ETSECCPB, UPC, Campus Nord B4, 08034, Barcelona, Catalonia, Spain", 
              "id": "http://www.grid.ac/institutes/grid.6835.8", 
              "name": [
                "CIRG, DFA, ETSECCPB, UPC, Campus Nord B4, 08034, Barcelona, Catalonia, Spain"
              ], 
              "type": "Organization"
            }, 
            "familyName": "Auguet", 
            "givenName": "C.", 
            "id": "sg:person.015263622177.64", 
            "sameAs": [
              "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.015263622177.64"
            ], 
            "type": "Person"
          }, 
          {
            "affiliation": {
              "alternateName": "CIRG, DFA, ETSECCPB, UPC, Campus Nord B4, 08034, Barcelona, Catalonia, Spain", 
              "id": "http://www.grid.ac/institutes/grid.6835.8", 
              "name": [
                "CIRG, DFA, ETSECCPB, UPC, Campus Nord B4, 08034, Barcelona, Catalonia, Spain"
              ], 
              "type": "Organization"
            }, 
            "familyName": "Isalgue", 
            "givenName": "A.", 
            "id": "sg:person.012300231413.68", 
            "sameAs": [
              "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.012300231413.68"
            ], 
            "type": "Person"
          }, 
          {
            "affiliation": {
              "alternateName": "Centro At\u00f3mico Bariloche and Instituto Balseiro, San Carlos de Bariloche, 8400, Argentina", 
              "id": "http://www.grid.ac/institutes/grid.418211.f", 
              "name": [
                "Centro At\u00f3mico Bariloche and Instituto Balseiro, San Carlos de Bariloche, 8400, Argentina"
              ], 
              "type": "Organization"
            }, 
            "familyName": "Lovey", 
            "givenName": "F. C.", 
            "id": "sg:person.010136741775.46", 
            "sameAs": [
              "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.010136741775.46"
            ], 
            "type": "Person"
          }, 
          {
            "affiliation": {
              "alternateName": "Facultad de Ciencias F\u00edsicas y Matem\u00e1ticas, Universidad de Chile, Beauchef 850, 8370448, Santiago, RM, Chile", 
              "id": "http://www.grid.ac/institutes/grid.443909.3", 
              "name": [
                "Facultad de Ciencias F\u00edsicas y Matem\u00e1ticas, Universidad de Chile, Beauchef 850, 8370448, Santiago, RM, Chile"
              ], 
              "type": "Organization"
            }, 
            "familyName": "Sepulveda", 
            "givenName": "A.", 
            "id": "sg:person.015416103445.03", 
            "sameAs": [
              "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.015416103445.03"
            ], 
            "type": "Person"
          }, 
          {
            "affiliation": {
              "alternateName": "Centro At\u00f3mico Bariloche and Instituto Balseiro, San Carlos de Bariloche, 8400, Argentina", 
              "id": "http://www.grid.ac/institutes/grid.418211.f", 
              "name": [
                "Centro At\u00f3mico Bariloche and Instituto Balseiro, San Carlos de Bariloche, 8400, Argentina"
              ], 
              "type": "Organization"
            }, 
            "familyName": "Soul", 
            "givenName": "H.", 
            "id": "sg:person.010334270632.18", 
            "sameAs": [
              "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.010334270632.18"
            ], 
            "type": "Person"
          }
        ], 
        "citation": [
          {
            "id": "sg:pub.10.1007/s10973-005-7480-3", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1031113997", 
              "https://doi.org/10.1007/s10973-005-7480-3"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s10973-007-8604-8", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1015027686", 
              "https://doi.org/10.1007/s10973-007-8604-8"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s10973-006-7625-z", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1022464446", 
              "https://doi.org/10.1007/s10973-006-7625-z"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s10973-005-0756-9", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1021238570", 
              "https://doi.org/10.1007/s10973-005-0756-9"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s10973-006-8034-z", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1017370615", 
              "https://doi.org/10.1007/s10973-006-8034-z"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s10973-007-8738-8", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1030549833", 
              "https://doi.org/10.1007/s10973-007-8738-8"
            ], 
            "type": "CreativeWork"
          }, 
          {
            "id": "sg:pub.10.1007/s10973-007-8600-z", 
            "sameAs": [
              "https://app.dimensions.ai/details/publication/pub.1011304488", 
              "https://doi.org/10.1007/s10973-007-8600-z"
            ], 
            "type": "CreativeWork"
          }
        ], 
        "datePublished": "2009-12-10", 
        "datePublishedReg": "2009-12-10", 
        "description": "The use of Shape Memory Alloys (SMA) in technical applications as damping in civil engineering structures requires the characterization of the alloy for each specific application. This involves the evolution of the mechanical properties and damping capacity with the number of cycles, frequency, maximum deformation, applied stresses, and the evolution of the alloy with aging time and temperature. In particular, the temperature effects associated to self-heating need to be evaluated. In continuous cycling the effects of latent heat, the associated dissipation induced by the hysteresis, the heat flow to surroundings and the cycling frequency induce different states of temperature in the specimen, which in turn produces changes in the transformation-retransformation stresses. In this article, the temperature effects associated to cycling are outlined for different cycling frequencies. The results show that, for relatively faster frequency the temperature arrives at an oscillatory state superimposed to an exponential increase. For lower frequencies, some parts of the sample attain temperatures below room temperature. The experimental results are represented with an elementary model (the 1-body model or the Tian equation used in calorimetric representation) of heat transfer. For the higher fracture where life requirements are associated to damping in stayed cables for bridges, the results show (for the NiTi alloy) a reduction of the hysteresis width as the frequency increases for deformations up to 8%. For reduced deformation, under 2% appears an asymptotic behavior where the frictional area is practically independent of the cycling frequency (up to 20\u00a0Hz). In addition, it is shown that more than 4\u00a0million of working cycles can be attained if the maximum applied stress is kept below a threshold of about 200\u00a0MPa. Although under this condition the deformation must remain lower than 2% a reasonable damping capacity can still be obtained.", 
        "genre": "article", 
        "id": "sg:pub.10.1007/s10973-009-0613-3", 
        "inLanguage": "en", 
        "isAccessibleForFree": false, 
        "isFundedItemOf": [
          {
            "id": "sg:grant.9276783", 
            "type": "MonetaryGrant"
          }
        ], 
        "isPartOf": [
          {
            "id": "sg:journal.1294862", 
            "issn": [
              "1388-6150", 
              "1572-8943"
            ], 
            "name": "Journal of Thermal Analysis and Calorimetry", 
            "publisher": "Springer Nature", 
            "type": "Periodical"
          }, 
          {
            "issueNumber": "2", 
            "type": "PublicationIssue"
          }, 
          {
            "type": "PublicationVolume", 
            "volumeNumber": "102"
          }
        ], 
        "keywords": [
          "shape memory alloy", 
          "civil engineering structures", 
          "maximum applied stress", 
          "cycling frequency", 
          "number of cycles", 
          "stayed cables", 
          "heat transfer", 
          "engineering structures", 
          "damping capacity", 
          "maximum deformation", 
          "mechanical properties", 
          "memory alloy", 
          "frictional area", 
          "temperature effects", 
          "latent heat", 
          "applied stress", 
          "martensitic transformation", 
          "reduced deformation", 
          "alloy", 
          "life requirements", 
          "deformation", 
          "higher fracture", 
          "heat flow", 
          "hysteresis width", 
          "technical applications", 
          "metastable effects", 
          "room temperature", 
          "different cycling frequencies", 
          "experimental results", 
          "temperature", 
          "associated dissipation", 
          "specific applications", 
          "continuous cycling", 
          "MPa", 
          "low frequency", 
          "cable", 
          "stress", 
          "elementary model", 
          "heat", 
          "applications", 
          "dissipation", 
          "hysteresis", 
          "frequency", 
          "oscillatory state", 
          "cycling", 
          "flow", 
          "fast frequency", 
          "specimen", 
          "capacity", 
          "cycle", 
          "bridge", 
          "properties", 
          "width", 
          "results", 
          "different states", 
          "fractures", 
          "effect", 
          "transfer", 
          "behavior", 
          "exponential increase", 
          "requirements", 
          "structure", 
          "conditions", 
          "characterization", 
          "evolution", 
          "model", 
          "surroundings", 
          "reduction", 
          "state", 
          "time", 
          "transformation", 
          "increase", 
          "addition", 
          "area", 
          "use", 
          "part", 
          "turn", 
          "threshold", 
          "asymptotic behavior", 
          "number", 
          "changes", 
          "need", 
          "article"
        ], 
        "name": "Metastable effects on martensitic transformation in SMA", 
        "pagination": "671-680", 
        "productId": [
          {
            "name": "dimensions_id", 
            "type": "PropertyValue", 
            "value": [
              "pub.1014929711"
            ]
          }, 
          {
            "name": "doi", 
            "type": "PropertyValue", 
            "value": [
              "10.1007/s10973-009-0613-3"
            ]
          }
        ], 
        "sameAs": [
          "https://doi.org/10.1007/s10973-009-0613-3", 
          "https://app.dimensions.ai/details/publication/pub.1014929711"
        ], 
        "sdDataset": "articles", 
        "sdDatePublished": "2022-05-10T09:56", 
        "sdLicense": "https://scigraph.springernature.com/explorer/license/", 
        "sdPublisher": {
          "name": "Springer Nature - SN SciGraph project", 
          "type": "Organization"
        }, 
        "sdSource": "s3://com-springernature-scigraph/baseset/20220509/entities/gbq_results/article/article_483.jsonl", 
        "type": "ScholarlyArticle", 
        "url": "https://doi.org/10.1007/s10973-009-0613-3"
      }
    ]
     

    Download the RDF metadata as:  json-ld nt turtle xml License info

    HOW TO GET THIS DATA PROGRAMMATICALLY:

    JSON-LD is a popular format for linked data which is fully compatible with JSON.

    curl -H 'Accept: application/ld+json' 'https://scigraph.springernature.com/pub.10.1007/s10973-009-0613-3'

    N-Triples is a line-based linked data format ideal for batch operations.

    curl -H 'Accept: application/n-triples' 'https://scigraph.springernature.com/pub.10.1007/s10973-009-0613-3'

    Turtle is a human-readable linked data format.

    curl -H 'Accept: text/turtle' 'https://scigraph.springernature.com/pub.10.1007/s10973-009-0613-3'

    RDF/XML is a standard XML format for linked data.

    curl -H 'Accept: application/rdf+xml' 'https://scigraph.springernature.com/pub.10.1007/s10973-009-0613-3'


     

    This table displays all metadata directly associated to this object as RDF triples.

    220 TRIPLES      22 PREDICATES      116 URIs      99 LITERALS      6 BLANK NODES

    Subject Predicate Object
    1 sg:pub.10.1007/s10973-009-0613-3 schema:about anzsrc-for:03
    2 anzsrc-for:0303
    3 anzsrc-for:0306
    4 anzsrc-for:0399
    5 schema:author Nb66129a12cc84e11975a4ff5f0fe6b18
    6 schema:citation sg:pub.10.1007/s10973-005-0756-9
    7 sg:pub.10.1007/s10973-005-7480-3
    8 sg:pub.10.1007/s10973-006-7625-z
    9 sg:pub.10.1007/s10973-006-8034-z
    10 sg:pub.10.1007/s10973-007-8600-z
    11 sg:pub.10.1007/s10973-007-8604-8
    12 sg:pub.10.1007/s10973-007-8738-8
    13 schema:datePublished 2009-12-10
    14 schema:datePublishedReg 2009-12-10
    15 schema:description The use of Shape Memory Alloys (SMA) in technical applications as damping in civil engineering structures requires the characterization of the alloy for each specific application. This involves the evolution of the mechanical properties and damping capacity with the number of cycles, frequency, maximum deformation, applied stresses, and the evolution of the alloy with aging time and temperature. In particular, the temperature effects associated to self-heating need to be evaluated. In continuous cycling the effects of latent heat, the associated dissipation induced by the hysteresis, the heat flow to surroundings and the cycling frequency induce different states of temperature in the specimen, which in turn produces changes in the transformation-retransformation stresses. In this article, the temperature effects associated to cycling are outlined for different cycling frequencies. The results show that, for relatively faster frequency the temperature arrives at an oscillatory state superimposed to an exponential increase. For lower frequencies, some parts of the sample attain temperatures below room temperature. The experimental results are represented with an elementary model (the 1-body model or the Tian equation used in calorimetric representation) of heat transfer. For the higher fracture where life requirements are associated to damping in stayed cables for bridges, the results show (for the NiTi alloy) a reduction of the hysteresis width as the frequency increases for deformations up to 8%. For reduced deformation, under 2% appears an asymptotic behavior where the frictional area is practically independent of the cycling frequency (up to 20 Hz). In addition, it is shown that more than 4 million of working cycles can be attained if the maximum applied stress is kept below a threshold of about 200 MPa. Although under this condition the deformation must remain lower than 2% a reasonable damping capacity can still be obtained.
    16 schema:genre article
    17 schema:inLanguage en
    18 schema:isAccessibleForFree false
    19 schema:isPartOf Nbca32a25c91b42cea7ff4e16de32356f
    20 Nbfe8d7a6982841f4ab18b32dc5cb91ca
    21 sg:journal.1294862
    22 schema:keywords MPa
    23 addition
    24 alloy
    25 applications
    26 applied stress
    27 area
    28 article
    29 associated dissipation
    30 asymptotic behavior
    31 behavior
    32 bridge
    33 cable
    34 capacity
    35 changes
    36 characterization
    37 civil engineering structures
    38 conditions
    39 continuous cycling
    40 cycle
    41 cycling
    42 cycling frequency
    43 damping capacity
    44 deformation
    45 different cycling frequencies
    46 different states
    47 dissipation
    48 effect
    49 elementary model
    50 engineering structures
    51 evolution
    52 experimental results
    53 exponential increase
    54 fast frequency
    55 flow
    56 fractures
    57 frequency
    58 frictional area
    59 heat
    60 heat flow
    61 heat transfer
    62 higher fracture
    63 hysteresis
    64 hysteresis width
    65 increase
    66 latent heat
    67 life requirements
    68 low frequency
    69 martensitic transformation
    70 maximum applied stress
    71 maximum deformation
    72 mechanical properties
    73 memory alloy
    74 metastable effects
    75 model
    76 need
    77 number
    78 number of cycles
    79 oscillatory state
    80 part
    81 properties
    82 reduced deformation
    83 reduction
    84 requirements
    85 results
    86 room temperature
    87 shape memory alloy
    88 specific applications
    89 specimen
    90 state
    91 stayed cables
    92 stress
    93 structure
    94 surroundings
    95 technical applications
    96 temperature
    97 temperature effects
    98 threshold
    99 time
    100 transfer
    101 transformation
    102 turn
    103 use
    104 width
    105 schema:name Metastable effects on martensitic transformation in SMA
    106 schema:pagination 671-680
    107 schema:productId N14949f26343c486bbe62d75132298be5
    108 N8cf764207e9e4c83baae53b07aac429f
    109 schema:sameAs https://app.dimensions.ai/details/publication/pub.1014929711
    110 https://doi.org/10.1007/s10973-009-0613-3
    111 schema:sdDatePublished 2022-05-10T09:56
    112 schema:sdLicense https://scigraph.springernature.com/explorer/license/
    113 schema:sdPublisher N2bdc0a8ea3b7461c92ecc7646bc4d6e3
    114 schema:url https://doi.org/10.1007/s10973-009-0613-3
    115 sgo:license sg:explorer/license/
    116 sgo:sdDataset articles
    117 rdf:type schema:ScholarlyArticle
    118 N14949f26343c486bbe62d75132298be5 schema:name doi
    119 schema:value 10.1007/s10973-009-0613-3
    120 rdf:type schema:PropertyValue
    121 N1a996b3c8035462cb2e98ebea35f450f rdf:first sg:person.015263622177.64
    122 rdf:rest Nf7c9907c6c1e4c868aaef2199e6c6187
    123 N2bdc0a8ea3b7461c92ecc7646bc4d6e3 schema:name Springer Nature - SN SciGraph project
    124 rdf:type schema:Organization
    125 N4843b60595af4a26b1ff0b60acfc9e58 rdf:first sg:person.010136741775.46
    126 rdf:rest Na6a2c9c625cd46b4b5f79e4ccc9ccd0a
    127 N70a9cbbaab4d41c5b49de84ae6f9f7cc rdf:first sg:person.010334270632.18
    128 rdf:rest rdf:nil
    129 N8cf764207e9e4c83baae53b07aac429f schema:name dimensions_id
    130 schema:value pub.1014929711
    131 rdf:type schema:PropertyValue
    132 Na6a2c9c625cd46b4b5f79e4ccc9ccd0a rdf:first sg:person.015416103445.03
    133 rdf:rest N70a9cbbaab4d41c5b49de84ae6f9f7cc
    134 Nb66129a12cc84e11975a4ff5f0fe6b18 rdf:first sg:person.013230703661.66
    135 rdf:rest N1a996b3c8035462cb2e98ebea35f450f
    136 Nbca32a25c91b42cea7ff4e16de32356f schema:volumeNumber 102
    137 rdf:type schema:PublicationVolume
    138 Nbfe8d7a6982841f4ab18b32dc5cb91ca schema:issueNumber 2
    139 rdf:type schema:PublicationIssue
    140 Nf7c9907c6c1e4c868aaef2199e6c6187 rdf:first sg:person.012300231413.68
    141 rdf:rest N4843b60595af4a26b1ff0b60acfc9e58
    142 anzsrc-for:03 schema:inDefinedTermSet anzsrc-for:
    143 schema:name Chemical Sciences
    144 rdf:type schema:DefinedTerm
    145 anzsrc-for:0303 schema:inDefinedTermSet anzsrc-for:
    146 schema:name Macromolecular and Materials Chemistry
    147 rdf:type schema:DefinedTerm
    148 anzsrc-for:0306 schema:inDefinedTermSet anzsrc-for:
    149 schema:name Physical Chemistry (incl. Structural)
    150 rdf:type schema:DefinedTerm
    151 anzsrc-for:0399 schema:inDefinedTermSet anzsrc-for:
    152 schema:name Other Chemical Sciences
    153 rdf:type schema:DefinedTerm
    154 sg:grant.9276783 http://pending.schema.org/fundedItem sg:pub.10.1007/s10973-009-0613-3
    155 rdf:type schema:MonetaryGrant
    156 sg:journal.1294862 schema:issn 1388-6150
    157 1572-8943
    158 schema:name Journal of Thermal Analysis and Calorimetry
    159 schema:publisher Springer Nature
    160 rdf:type schema:Periodical
    161 sg:person.010136741775.46 schema:affiliation grid-institutes:grid.418211.f
    162 schema:familyName Lovey
    163 schema:givenName F. C.
    164 schema:sameAs https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.010136741775.46
    165 rdf:type schema:Person
    166 sg:person.010334270632.18 schema:affiliation grid-institutes:grid.418211.f
    167 schema:familyName Soul
    168 schema:givenName H.
    169 schema:sameAs https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.010334270632.18
    170 rdf:type schema:Person
    171 sg:person.012300231413.68 schema:affiliation grid-institutes:grid.6835.8
    172 schema:familyName Isalgue
    173 schema:givenName A.
    174 schema:sameAs https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.012300231413.68
    175 rdf:type schema:Person
    176 sg:person.013230703661.66 schema:affiliation grid-institutes:grid.6835.8
    177 schema:familyName Torra
    178 schema:givenName V.
    179 schema:sameAs https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.013230703661.66
    180 rdf:type schema:Person
    181 sg:person.015263622177.64 schema:affiliation grid-institutes:grid.6835.8
    182 schema:familyName Auguet
    183 schema:givenName C.
    184 schema:sameAs https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.015263622177.64
    185 rdf:type schema:Person
    186 sg:person.015416103445.03 schema:affiliation grid-institutes:grid.443909.3
    187 schema:familyName Sepulveda
    188 schema:givenName A.
    189 schema:sameAs https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.015416103445.03
    190 rdf:type schema:Person
    191 sg:pub.10.1007/s10973-005-0756-9 schema:sameAs https://app.dimensions.ai/details/publication/pub.1021238570
    192 https://doi.org/10.1007/s10973-005-0756-9
    193 rdf:type schema:CreativeWork
    194 sg:pub.10.1007/s10973-005-7480-3 schema:sameAs https://app.dimensions.ai/details/publication/pub.1031113997
    195 https://doi.org/10.1007/s10973-005-7480-3
    196 rdf:type schema:CreativeWork
    197 sg:pub.10.1007/s10973-006-7625-z schema:sameAs https://app.dimensions.ai/details/publication/pub.1022464446
    198 https://doi.org/10.1007/s10973-006-7625-z
    199 rdf:type schema:CreativeWork
    200 sg:pub.10.1007/s10973-006-8034-z schema:sameAs https://app.dimensions.ai/details/publication/pub.1017370615
    201 https://doi.org/10.1007/s10973-006-8034-z
    202 rdf:type schema:CreativeWork
    203 sg:pub.10.1007/s10973-007-8600-z schema:sameAs https://app.dimensions.ai/details/publication/pub.1011304488
    204 https://doi.org/10.1007/s10973-007-8600-z
    205 rdf:type schema:CreativeWork
    206 sg:pub.10.1007/s10973-007-8604-8 schema:sameAs https://app.dimensions.ai/details/publication/pub.1015027686
    207 https://doi.org/10.1007/s10973-007-8604-8
    208 rdf:type schema:CreativeWork
    209 sg:pub.10.1007/s10973-007-8738-8 schema:sameAs https://app.dimensions.ai/details/publication/pub.1030549833
    210 https://doi.org/10.1007/s10973-007-8738-8
    211 rdf:type schema:CreativeWork
    212 grid-institutes:grid.418211.f schema:alternateName Centro Atómico Bariloche and Instituto Balseiro, San Carlos de Bariloche, 8400, Argentina
    213 schema:name Centro Atómico Bariloche and Instituto Balseiro, San Carlos de Bariloche, 8400, Argentina
    214 rdf:type schema:Organization
    215 grid-institutes:grid.443909.3 schema:alternateName Facultad de Ciencias Físicas y Matemáticas, Universidad de Chile, Beauchef 850, 8370448, Santiago, RM, Chile
    216 schema:name Facultad de Ciencias Físicas y Matemáticas, Universidad de Chile, Beauchef 850, 8370448, Santiago, RM, Chile
    217 rdf:type schema:Organization
    218 grid-institutes:grid.6835.8 schema:alternateName CIRG, DFA, ETSECCPB, UPC, Campus Nord B4, 08034, Barcelona, Catalonia, Spain
    219 schema:name CIRG, DFA, ETSECCPB, UPC, Campus Nord B4, 08034, Barcelona, Catalonia, Spain
    220 rdf:type schema:Organization
     




    Preview window. Press ESC to close (or click here)


    ...