Young Hoon Moon


Ontology type: schema:Person     


Person Info

NAME

Young Hoon

SURNAME

Moon

Publications in SciGraph latest 50 shown

  • 2018-10-17 Process-induced defects in an L-shape profile ring rolling process in INTERNATIONAL JOURNAL OF MATERIAL FORMING
  • 2018-10 Advanced induction heating system for hot stamping in THE INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
  • 2018-07 Application of segmented rubber rings to increase the sealing efficiency in hydroforming in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2018-04 Feasibility studies on manufacturing tailored blanks by rolling partially stacked blanks in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2017-09 Feasibility studies of laser surface nitriding on Ti-6Al-4V alloy using a nitric acid solution in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2017-09 Evolution of microstructure and mechanical properties of SUS430/C11000/SUS430 composites during the laser-forming process in METALS AND MATERIALS INTERNATIONAL
  • 2016-12 Effect of loading pattern on longitudinal bowing in flexible roll forming in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2016-11 Prediction of turn down warping during hot plate rolling based on a Gaussian function in INTERNATIONAL JOURNAL OF MATERIAL FORMING
  • 2016-05 Laser bendability of SUS430/C11000/SUS430 laminated composite and its constituent layers in METALS AND MATERIALS INTERNATIONAL
  • 2016-05 Fabrication and characterization of roll-formed aluminum heat shield in INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING
  • 2015-12 The effect of mechanical properties on hole flangeability of stainless steel sheets in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2015-05 Stabilization of Oxygen-deficient Structure for Conducting Li4Ti5O12-δ by Molybdenum Doping in a Reducing Atmosphere in SCIENTIFIC REPORTS
  • 2015-02 Flexible roll forming process design for variable cross-section profile in INTERNATIONAL JOURNAL OF AUTOMOTIVE TECHNOLOGY
  • 2014-12 Friction effect of surface treated tools used for warm forming of Mg alloy sheets in INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING
  • 2014-10 Enhancing tube hydroformability by reducing the local strain gradient at potential necking sites in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2014-07 Feasibility study on optimized process conditions in warm tube hydroforming in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2013-09 Deformation analysis for cold rolling of Al-Cu double layered sheet by physical modeling and finite element method in METALS AND MATERIALS INTERNATIONAL
  • 2013-05 Characterization of deposited layer fabricated by direct laser melting process in METALS AND MATERIALS INTERNATIONAL
  • 2013-05 Reliability analysis of stainless steel/carbon steel double-layered tube on the basis of thermal deformation behavior in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2013-01 FMEA for the reliability of hydroformed flanged part for automotive application in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2013-01 Process analysis of two-layered tube hydroforming with analytical and experimental verification in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2012-07 Reliability analysis of process-induced cracks in rotary swaged shell nose part in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2012-06 The effect of tube dimensions on optimized pressure and force loading paths in tube hydroforming process in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2011-02 Application of direct laser melting to restore damaged steel dies in METALS AND MATERIALS INTERNATIONAL
  • 2009-12 Effect of hardness of the piston ring coating on the wear characteristics of rubbing surfaces in METALS AND MATERIALS INTERNATIONAL
  • 2009-12 Strain hardening behavior during manufacturing of tube shapes by hydroforming in METALS AND MATERIALS INTERNATIONAL
  • 2005-06 Deformation behavior of a slab with width reduction in a hot mill in JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
  • 2005-04 Feasibility of electro-slag cast steel for hot-working tools in METALS AND MATERIALS INTERNATIONAL
  • 2005-02 Thermal and mechanical properties of electro-slag cast steel for hot working tools in JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
  • 2004-06 Control Scheme Using Forward Slip for a Multi-stand Hot Strip Rolling Mill in KSME INTERNATIONAL JOURNAL
  • 2001-04 Deep drawing with internal air-pressing to increase the limit drawing ratio of aluminum sheet in KSME INTERNATIONAL JOURNAL
  • 2000-02 Induction heating of semisolid billet and control of globular microstructure to prevent coarsening phenomena in JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
  • Affiliations

    JSON-LD is the canonical representation for SciGraph data.

    TIP: You can open this SciGraph record using an external JSON-LD service: JSON-LD Playground Google SDTT

    [
      {
        "@context": "https://springernature.github.io/scigraph/jsonld/sgcontext.json", 
        "affiliation": [
          {
            "affiliation": {
              "id": "https://www.grid.ac/institutes/grid.262229.f", 
              "type": "Organization"
            }, 
            "isCurrent": true, 
            "type": "OrganizationRole"
          }
        ], 
        "familyName": "Moon", 
        "givenName": "Young Hoon", 
        "id": "sg:person.015202214425.94", 
        "sameAs": [
          "https://app.dimensions.ai/discover/publication?and_facet_researcher=ur.015202214425.94"
        ], 
        "sdDataset": "persons", 
        "sdDatePublished": "2019-03-07T13:47", 
        "sdLicense": "https://scigraph.springernature.com/explorer/license/", 
        "sdPublisher": {
          "name": "Springer Nature - SN SciGraph project", 
          "type": "Organization"
        }, 
        "sdSource": "s3://com-uberresearch-data-dimensions-researchers-20181010/20181011/dim_researchers/base/researchers_1560.json", 
        "type": "Person"
      }
    ]
     

    Download the RDF metadata as:  json-ld nt turtle xml License info

    HOW TO GET THIS DATA PROGRAMMATICALLY:

    JSON-LD is a popular format for linked data which is fully compatible with JSON.

    curl -H 'Accept: application/ld+json' 'https://scigraph.springernature.com/person.015202214425.94'

    N-Triples is a line-based linked data format ideal for batch operations.

    curl -H 'Accept: application/n-triples' 'https://scigraph.springernature.com/person.015202214425.94'

    Turtle is a human-readable linked data format.

    curl -H 'Accept: text/turtle' 'https://scigraph.springernature.com/person.015202214425.94'

    RDF/XML is a standard XML format for linked data.

    curl -H 'Accept: application/rdf+xml' 'https://scigraph.springernature.com/person.015202214425.94'


     




    Preview window. Press ESC to close (or click here)


    ...